The process of covering a bare tree with a white synthetic powder gives the illusion of a fresh snow dusting while retaining the tree’s natural charm. While store-bought flocked trees are an acceptable alternative, doing it yourself is both time consuming and labor intensive.
Table of Contents
Can you use spray snow to flock a Christmas tree?
I flock my tree and let it dry, I use the spray snow and spray some areas to thicken it up and create the look of a heavy layer of snow. I use about 5 cans of snow spray on my tree and love it. You can add other decorations to your tree.
Can you flock a tree with baking soda?
I wanted them to be covered in thick snow. When they were covered as I desired, I sprayed on more adhesive and poured baking soda over each tree and under the branches as well. This gave the snow on the trees a thicker look.
Once the trees were completely covered in snow, it was time to put them in the freezer for a couple of hours to harden them up a bit. Once they had hardened, the next step was to paint them. I used a mixture of white acrylic paint and white paint to give the tree’s bark a glossy finish.
I painted each branch with a thin coat of black paint, followed by another thin layer of paint on top of that, and then a final coat on the trunk and branches.
I let the paint dry for about an hour and a half, then I wiped off the excess paint with an old toothbrush and let it dry completely before painting the rest of the branch and trunk with the same paint. The tree was then ready to go back into the oven for another hour or so, until the bark was completely dry.
How do you flock a Christmas tree with shaving cream?
form. You will need to make 3-4 batches to get the right consistency if you are flocking an entire tree. Once you have the consistency you want, you can use a toothpick to poke holes in the foam to allow air to escape. You can also use your fingers to push the air out of the holes.
Once you are happy with the amount of air that is escaping from your foam, it’s time to apply it to the tree. I used a brush to spread the cream all over my tree and let it sit for a few minutes. I applied a thin layer of cream to each of my branches.
You will want to be careful to not apply too much cream at one time, as it will make your tree look like it has a lot of foam on it. After you apply your first layer, apply another layer and repeat the process until all of your branches are covered in foam. The more layers you add, the more dense and dense your trees will look.
How do you seal a flocking Christmas tree?
Use a spray bottle to lightly mist a section of the tree. Take some of the flocking powder out of the strainer and put it on the tree. The tree should be sprayed with water again. The water fluffs up the flocking and seals it in place.
Can you flock your own Christmas tree?
When you’re ready to begin the process of flocking, fill a spray bottle with water and start with one section of the tree. The flocking should be put on the tree once the needles are damp. You can shake the flocking through a sifter positioned over a bowl of water to get more coverage. Once the trees are flocked, it’s time to move on to the next stage.
The next step is to remove the leaves from the branches. You can do this with a pair of tweezers or a sharp knife. If you don’t have a tweezer, use your fingers to gently pull the leaf off the branch. Be careful not to pull too hard, as this can damage the bark and cause it to fall off.
How long does flocking take to dry?
Set aside your project to dry for 10 to 15 hours after you have applied enough fibres. The project may be turned upside down to remove excess fibre before the drying process is completed. Fibres should be removed from the fabric as soon as possible after they have dried. This will ensure that they will not be damaged during the washing process.
What is Christmas tree flocking powder made of?
Nurseries commonly use flocking made of cotton fibers or cellulose, spray adhesive and water. Christmas tree flockings are made from cotton fibers, water, spray glue, and/or a combination of the two.
Flocking can be used in a variety of ways, but the most common is to use it as an adhesive to attach a tree to a wall or ceiling. It can also be applied directly to the tree’s trunk, branches or leaves.
Flocking is also used as a decorative feature on trees and shrubs, as well as on other decorative items.